Element TV wont turn on [100% fixed]

There is no need to worry if your Element TV wont turn on. Today we are going to tell you some such methods through which your problem will be solved.

You can troubleshoot at home using the methods mentioned. Before delving into detail troubleshooting, let us know the quick answer. Because of this, you can solve the problem quickly.

Quick Answer: You can use the power cycling method to fix Element TV. First of all, you have to unplug the Element TV and wait for 5 minutes. After removing the plug, you have to press the power button for 1 to 2 minutes. Now you have to plug the TV into the socket and turn the switch ON.

If your problem is not solved through a power cycle then you can go towards detail troubleshooting.

Before starting the detailed troubleshooting, let us know why won’t my element TV turn on.

Why Element TV wont turn on?

There can be many reasons for Element TV wont turn on. The main reasons for this happening could be insufficient power supply or a temporary glitch in the software.

Or maybe the power cable is broken. Let’s stop guessing now and find out why Element TV won’t turn on

Problem with the power cable:

Even if the power cable of your Element TV is damaged, the Element TV won’t turn on.

Insufficient power supply:

It is also possible that there may be some problem with the power supply of Element TV.

Component Failure:

It is possible that there may be a problem with the Element TV’s motherboard, backlight, or any component such as capacitors or fuse.

Remote not working:

IR sensor does not work due to dead batteries present in the remote. Or the circuit board of the remote itself may have been damaged.

Software Crash:

Element TV won’t turn on due to software files, app crashes, or system overheating.

The main parts of Element TV

Before troubleshooting Element TV, let us know about some main components. We are only going to give an overview, it will not be too technical.

It is also important to know these because defective components have different symptoms. It is very important to find out which part of the TV is defective. Knowing this makes it easier to repair that component.

There are 4 main components in any LED TV. These are like this:

• Power Supply
• Motherboard
• TCON Board
• Backlight

Power Supply:

The circuit board of the power supply is under the back cover of the TV. It supplies current to the motherboard and other components.

There are many transistors and capacitors on this board. If there is any fluctuation in electricity then due to that also the components installed in the power board may get damaged.

Motherboard:

The motherboard is considered the core of the TV. There are many capacitors, transistors, and registers inside it.

Through this board, the video is processed and the signal is sent to the TCON (Timing Control Board) board. The video is then shown on the screen.

TCON Board:

TCON is called the Time Control Board. It is located at the top or bottom of the LCD panel. With its help, the position of horizontal and vertical lines on the TV is defined.

A TCON board manages half the screen. The other TCON board manages the other half screen.

If even one TCON board fails then viewing of images on one side will stop.

Backlight:

LED strips or CCFL tubes are used for backlight behind the LCD screen. Through this, the images of the LCD screen are illuminated.

These backlights get damaged when they get too old, Especially CCFL tubes.

After knowing the main components of TV, now we will easily understand the problem of Element TV won’t turn on.

Element TV Sign of malfunction and Possible reasons

If any TV has any problem then it gives some signs. By looking at these signs, it can be found out what is the problem with the TV.

Now we are going to talk about these signs.

Element TV wont turn ON [8 ways Troubleshooting]

For your information, let me tell you that this post is only a troubleshooting guide, not a repair guide. Therefore, all the methods mentioned in it start from simple and end with hard methods.

Once you know the problem, you can repair it yourself or get help from a professional.

You can save hundreds of bucks by trying these methods yourself. These methods can also be applied to TVs like Samsung, LG, and Sharp.

Method #1. Check the Wall Power Source

Whenever any electronic device malfunctions, the first thing to be checked is whether the current is coming from the wall socket or not.

Similarly, the wall socket to which Element TV is connected. You can check whether it has power or not through a tester.

You will be surprised to know that in more than half of the cases, such problems are seen due to loose wire or short circuit of the wall socket.

You can test the wall power circuit with a tester, multimeter, or any other appliance such as a phone charger.

All you have to do is take the appliance and connect the appliance to the same socket with which you connect the TV.

If you use this method and the wall power circuit turns out to be bad, you can save hundreds of bucks.

If you use a voltage tester or multimeter, the tester’s light turns ON or the reading is correct, which means the socket is working properly. This means that there is a fault in Element TV. Because of this Element TV won’t turn ON.

Method #2. Check Power Cord

Now you have to check the power cord of Element TV very carefully. Things to note in the cord are that there should not be visible cuts, splitting, or breaks.

If the power cord is damaged somewhere, change it immediately. Also, check that the power cord is inserted into the TV and socket from both ends.

Whenever the power cord plug and wall socket are not connected properly, both start getting hot. If this happens for too long, both can be damaged.

Method #3. Perform a Power Cycle

If the power cord and power socket of your TV are correct then you can perform the power cycle method.

By this method, the power current present in the TV gets discharged. When you turn on the TV again, a clean boot is provided.

The power cycle sounds fancy, but in this, you only have to turn the Element TV OFF and then ON again.

To perform a power cycle on Element TV, you must follow the steps given below.

• First of all, the TV has to be unplugged from the wall socket.
• Now you have to wait for 5 minutes.
• There will be a power button at the bottom of the TV, you have to press and hold it for a few seconds.
• The TV plug has to be reattached to the socket. Have to turn it on.

Method #4. Try Pressing the Power Button

Before using the remote, try pressing the manual button of the TV once. Power buttons may be in different places in different models.

• In some models, the power button is on the side edge of the monitor.
• In some models, it is at the bottom of the Element logo.

Now press and hold the power button for 30 seconds. If this doesn’t work then you can move towards the next method.

Method #5. Check the ELEMENT TV remote batteries

It has been seen that the problem can occur not only in Element TV but also in the remote.

If the power light of your TV is turning ON but there is no response when you press the button on the remote, then it is possible that the problem is not with the TV but with the remote.

The first way to troubleshoot the remote is to start by checking the battery.

First of all, you have to buy a new pair of alkaline batteries. But keep in mind that do not mix brand or old batteries.

There may be voltage fluctuations when batteries of different brands are used. Due to this remote damage can occur.

Method #6. Clean The Remote

Element TV won’t turn on even due to a faulty remote. In such a case you can clean the remote.

Due to the old remote, many dust particles settle on the remote. Due to this, the buttons become hard to press.

There is a circuit below the buttons, but due to dust, a layer is formed between them. It is also called the dust layer.

Due to this layer, there is no contact with the circuit when the button is pressed and the remote does not work.

You won’t have to do much for this. First of all, you have to open some screws of the remote.

After this, the rubber of the button and the circuit board have to be separated. But keep in mind that the circuit board is very delicate. Too much pressure may break the circuit board.

Clean the rubber and circuit with a clean cloth. After this reassemble the remote. One more thing, clean the battery compartment of the remote also.

After this, reassemble the remote by screwing it properly.

Method #7. Check the Remote IR sensor

Every remote has an IR sensor. This sensor is present in the front part of the remote. Through this, you can check whether the IR sensor is producing a signal or not.

Every remote has an IR sensor. This sensor is present in the front part of the remote. Through this, you can check whether the IR sensor is producing a signal or not.

When you press the button on the remote, an infrared signal is produced.

However, the infrared signal is not visible directly to the eyes. In such a situation, you can take the help of a mobile camera.

For this, you have to recode the video from the phone’s camera and keep the phone’s camera in the direction where the IR sensor is installed.

When you are recording the video from the phone, you have to press some buttons from the remote and check whether the IR sensor is working or not.

To do this process, the lights of the room have to be switched off. After this, the video has to be made with a mobile in the dark.

After making the video, you can watch it by playing it back.

If the IR light is blinking when you press the remote button, then your remote is working properly. If it is not so then the IR light has been damaged. In this condition, you can replace the IR light or buy a new remote.

Method #8. Remove All External Devices

If you have used all the methods mentioned above and Element TV not turning ON. In such a situation, you can up-plug external devices to the TV.

Many times such issues are seen due to external devices also. Such as a set-top box, HDMI, Pendrive, LAN cable to connect to the internet, streaming device (Roku)

All the devices connected to the TV have to be disconnected one by one. Only the power cable should be connected to the Element TV.

Now you have to turn on Element TV and watch it. If the TV turns on then there is a problem with one of your internal devices. If this does not happen then the problem is with the TV. You can move to the next method.

Conclusion

In this post we learned how to fix Element TV won’t turn ON. Do let us know by commenting whether this post solved your problem or not.

If your problem is still not solved then you can talk to the customer care of Element TV. Because we know that troubleshooting the device is not easy.

FAQ (Frequently Asked Questions)